Spark Plug Replacement — Nissan Altima DIY Guide

Worn spark plugs cause misfires, poor mileage, and rough idle. Replacement is one of the most rewarding DIY jobs — you'll feel the difference immediately. On the Nissan Altima (1992-present), this job typically takes about 60 minutes and uses 2.5L NA I4-spec parts.

Nissan Altima Specs

  • Production years: 1992-present (6th gen 2019+)
  • Engines: 2.5L NA I4, 2.0L VC-Turbo I4
  • Lug nut torque: 80 ft-lbs
  • Oil capacity: 5.1 qts (0W-20 full synthetic)
  • Brake fluid: DOT 3

Common Nissan Altima issues: CVT failure (extended warranty 2013-2018); Oxygen sensor failures; Window regulator failures.

Pro tip: If the CVT shudders or whines under load, drain and refill with genuine NS-3 fluid before assuming failure — many issues are fluid-related.

Symptoms

  • Engine misfires or hesitation
  • Rough idle
  • Poor fuel economy
  • Hard starting
  • Check engine light (P0300-P0308)

Tools

  • Spark plug socket (5/8" or 13/16")
  • Ratchet and extension
  • Torque wrench
  • Anti-seize compound
  • Dielectric grease

Steps

  1. Let the engine cool completely: Hot aluminum heads strip threads easily. Wait at least 2 hours after running.
  2. Remove the engine cover: Most modern engines have a plastic cover that pulls straight off.
  3. Disconnect one ignition coil: Work on one cylinder at a time so you can't mix up firing order. Squeeze the connector tab and pull off the wire, then unbolt the coil pack and lift it out.
  4. Remove the old spark plug: Use a spark plug socket with a long extension. Turn counterclockwise. If it's hard to turn, stop and apply penetrating oil — never force it.
  5. Gap the new plug: Most pre-gapped plugs are fine, but verify with a gap gauge. Check your owner's manual for the spec (usually 0.028-0.044").
  6. Apply anti-seize: Put a tiny dab of anti-seize on the threads (not on the electrode tip). This makes the next change much easier.
  7. Hand-thread the new plug: Always start by hand to avoid cross-threading. Once snug, finish with a torque wrench to manufacturer spec — usually 15-25 ft-lbs.
  8. Reinstall the coil: Apply a small amount of dielectric grease inside the boot. Press the coil down firmly and reconnect the wire.
  9. Repeat for each cylinder: One at a time, then reinstall the engine cover. Start the engine — it should idle smoother than before.

Safety Notes

  • Engine must be fully cool before removing plugs
  • Never force a stuck plug — apply penetrating oil
  • Always torque to spec — over-tightening damages the head

FAQ

What's the lug nut torque spec for the Nissan Altima?

80 ft-lbs in a star pattern. Always finish with a torque wrench, never an impact gun.

What engines does the Nissan Altima use, and does that change this job?

Common Nissan Altima engines include 2.5L NA I4, 2.0L VC-Turbo I4. The procedure is the same across engines, but oil capacity and torque values may vary — confirm against your owner's manual before final assembly.

Are there known Nissan Altima issues to watch for during this job?

Yes — the most common Nissan Altima issues to inspect are: CVT failure (extended warranty 2013-2018); Oxygen sensor failures; Window regulator failures. While you have the wheel off or the engine open, take 60 seconds to look for these.

When should I replace spark plugs?

Copper: 30,000 miles. Platinum: 60,000 miles. Iridium: 100,000+ miles. Check your owner's manual.

Should I replace all plugs at once?

Yes. They wear at similar rates and replacing them together prevents future misfire issues.

Do I need to replace coils too?

Only if a coil is bad (causing a specific cylinder misfire code). Otherwise they last 100,000+ miles.